PLUMBING BASICS: BEFORE INSTALLING A BATHTUB

Plumbing Basics: Before Installing a Bathtub

Plumbing Basics: Before Installing a Bathtub

Blog Article

Call

We've unearthed the article pertaining to Tools You Need to Install a New Bathtub down the page on the web and reckoned it made perfect sense to discuss it with you here.


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Installing a tub isn't exactly brain surgery, however it does call for solid plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old tub with a new one is likewise a reasonably difficult job. If the old bathtub is readily obtainable, the project can move easily; if you have to open up a wall surface to remove the old tub and also place the brand-new bathtub, the task is much harder. In either instance, the job is within a home handyman's abilities, although you will certainly need a helper to vacate the old tub as well as set in the new one. Make sure you have actually certified yourself for the job and also fit attempting it. Instead of hiring a contractor to take control of a halfway-completed job, it is better to take into consideration employing one prior to you begin. Possibilities are you may need a specialist plumber to make tube connections.
This article will certainly aid you install a brand-new bath tub in your shower room if you have actually already acquired a new tub as well as do not require to change the plan of your previous water pipes.
Your tools and product list should comprise the following:
  • New Tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipeline Caps


  • Planning for the Installment


    To start with, the sustaining framework provided with the bath must be fitted (if needed) according to the maker's directions. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is important to see to it that if the tap comes with a plastic washer, it is fitted between the bath and the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the faucets system to prevent pressure on the tub.
    Fit the flexible faucet connectors to the bottom of both taps making use of 2 nuts and also olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you utilize every one of the provided washing machines.
    Connect the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom must currently be ready to be fitted in its final position.

    Removing Old Touches


    If you require to change old faucets with new ones as a part of your setup, then the first thing you need to do is disconnect the supply of water. After doing so, turn on the faucets to drain pipes any water remaining in the system. The procedure of eliminating the existing taps can be quite bothersome because of the restricted access that is frequently the case.
    Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the taps. Have a fabric all set for the continuing to be water that will come from the pipes. Once the supply pipelines have been eliminated, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from transforming during this process. As soon as the taps have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any kind of old sealing substance.
    Before proceeding to fit the brand-new taps, compare the pipe links on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, then a shank adapter is required for the new taps to fit.

    Mounting the Bathtub


    Utilizing both wood boards under its feet, put the bathtub in the needed position. The wood boards are useful in equally spreading out the weight of the tub over the location of the boards instead of focusing all the weight onto four small factors.
    The following objective is to make sure that the bath tub is leveled all round. This can be attained by examining the spirit level as well as changing the feet on the bathtub until the level checks out level.
    To install taps, fit all-time low of the furthest adaptable faucet connector to the suitable supply pipe by making a compression sign up with; after that do the very same for the various other faucet.
    Turn on the water system and examine all joints and also new pipework for leaks as well as tighten them if essential. Fill the tub as well as also check the overflow outlet and also the typical outlet for leaks.
    Lastly, fix the bathroom paneling as described in the maker's user's manual. Tiling as well as securing around the bathtub ought to wait until the tub has been used at least when as this will resolve it right into its final position.

    Suitable New Touches


    If the tails of the new taps are plastic, after that you will certainly need a plastic port to prevent damage to the thread. One end of the connector fits on the plastic tail of the faucet and the various other end provides a link to the existing supply pipelines.
    If you require to fit a monobloc, then you will certainly need minimizing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
    Next, position the faucet in the mounting opening in the bath/basin ensuring that the washing machines are in area between the tap and the sink. Safeguard the tap in place with the maker given backnut. When the faucet is safely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with normal faucet ports. The former kind must be linked to the tap ends initially, tightening just by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been linked.

    Tiling Around the Bath tub


    In the area where the bathroom satisfies the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is important as the installation can relocate sufficient to crack a rigid seal, causing the water to penetrate the wall between the bath as well as the tiling, bring about complications with dampness and possible leakages to the ceiling listed below.
    You can select from a selection of coloured sealers to blend in your fixtures and installations. They are offered in tubes and also cartridges, as well as can sealing voids up to a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of soaked newspaper or soft rope. Bear in mind to constantly fill the bath tub with water before securing, to permit the motion experienced when the bathtub remains in usage. The sealer can fracture rather early if you do not take into account this activity before sealing.
    Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise quickly offered on the market. It is advisable to fit the floor tiles making use of waterproof or waterproof glue and cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

    I was made aware of that article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround through an associate on our other blog. In case you enjoyed reading our post plz do not forget to pass it around. Thanks a lot for your time. Please check our website back soon.


    Request our service.

    Report this page